Showing posts with label Free Ringtones. Show all posts
Showing posts with label Free Ringtones. Show all posts

Wednesday 4 April 2012

Free Ringtones

Free Ringtones Biography:

A phone “rings” when its network indicates an incoming call and the phone thus alerts the user. For land line telephones, the call signal can be an electric current generated by the switch or exchange to which the telephone is connected. For mobile phones, the network sends the phone a message indicating an incoming call.
A telephone “ring” is the sound generated when there is an incoming telephone call. The term originated from the fact that telephones originally had a ringing mechanism consisting of bells and an electromagnetically-driven clapper, producing a ringing sound. The aforementioned electrical signal powered the electromagnets which would rapidly move and release the clapper, striking the bells. This electromagnetic bell system is still in widespread use. The ringing signal sent to a customer's telephone is 90 volts AC at a frequency of 20 hertz in North America. In Europe it is around 60-90 volts AC at a frequency of 25 hertz. Some non-Bell system party lines in the US used multiple frequencies (20/30/40Hz, 22/33/44 Hz, etc.) to allow "selective" ringing.
In Australia the ring signal averages 100 V AC at 25 Hz.[1]
While the sound produced is still called a “ring”, more-recently manufactured telephones electronically produce a warbling, chirping, or other sound. Variation of the ring signal can be used to indicate characteristics of incoming calls (for example, rings with a shorter interval between them might be used to signal a call from a given number).
A ringing signal is an electric telephony signal that causes a telephone to alert the user to an incoming call. On a POTS interface, this signal is created by superimposing ringing voltage [90 volts AC at 20 Hz in the USA] atop the -48VDC already on the line. This is done at the Central Office, or a neighborhood multiplexer called a "SLC" for Subscriber Line Carrier. (SLC is a trademark of Alcatel-Lucent, but is a term often used generically.]
This ring voltage came from various sources. In large Central Offices, there were 48VDC motor-driven generator sets for both ringing & other signals such as dial tone and busy signals. In smaller offices, a special Sub-Cycle magnetic oscillator was used. More recently, solid-state oscillators have replaced them.
In old phones, this voltage was used to trigger a high-impedance electromagnet to ring a bell on the phone. Fixed phones of the late 20th century and later detect this ringing current voltage and trigger a warbling tone electronically. Mobile phones are fully digital, hence are signaled to ring as part of the protocol they use to communicate with the cell base stations.
In POTS switching systems, ringing is said to be "tripped" when the impedance of the line reduces to about 600 ohms when the telephone handset is lifted off the switch-hook. This signals that the telephone call has been answered, and the telephone exchange immediately removes the ringing signal from the line and connects the call. This is the source of the name of the problem called "ring-trip" or "pre-trip", which occurs when the ringing signal on the line encounters excessively low resistance between the conductors, which trips the ring before the subscriber's actual telephone has a chance to ring (for more than a very short time); this is common with wet connections and improperly installed lines.
Early research showed that people would wait until the phone stopped ringing before picking it up.[citation needed] Breaks were introduced into the signal to avoid this problem, resulting in the common ring-pause-ring cadence pattern used today. In early party line systems this pattern was a Morse code letter indicating who should pick up the phone, but today, with individual lines, the only surviving patterns are a single ring and double-ring, originally Morse code letters T (dash) and M (dash dash).[clarification needed]
The ringing pattern is known as ring cadence. This only applies to POTS fixed phones, where the high voltage ring signal is switched on and off to create the ringing pattern. In North America, the standard ring cadence is "2-4", or two seconds of ringing followed by four seconds of silence. In Australia and the UK, the standard ring cadence is 400 ms on, 200 ms off, 400 ms on, 2000 ms off. These patterns may vary from region to region, and other patterns are used in different countries around the world.
A service akin to party line ringing is making a comeback in some small office and home office situations allowing facsimile machines and telephones to share the same line but have different telephone numbers; this CLASS feature is usually called distinctive ringing generically, though carriers assign it trademarked names such as "Smart Ring", "Duet", "Multiple Number", "Ident-a-Call", and "Ringmaster." This feature is also used for a second phone number assigned to the same physical line for roommates or teenagers, in which case it is sometimes marketed under the name "teen line".
Caller ID signals are sent during the silent interval between the first and second bursts of the ringing signals.
The interrupted ring signal was designed to attract attention and studies showed that an intermittent two tone ring was the easiest to hear.[citation needed] This had nothing to do with the coded ringing that was used on party lines.
[edit]History
AT&T offered seven different gong combinations for the "C" type ringer found in the model 500 and 2500 land-line telephone sets. These gongs provided "distinctive tones" for hearing-impaired customers and to make it possible to tell which phone was ringing when several phones were placed closely together.[2] A "Bell Chime" was also offered, which could be set to chime like a doorbell or to ring like an ordinary phone.
Following a 1975 FCC ruling which permitted third-party devices to be connected to phone lines, manufacturers began to produce accessory telephone ringers which rang with electronic tones or melodies rather than mechanically. People also made their own ringers which used the chip from a musical greeting card to play a melody on the arrival of a call.[3] One such ringer, described in a 1989 book, even features a toy dog which barks and wags its tail when a call arrives.[4] Eventually, electronic telephone ringers became the norm. Some of these ringers produced a single tone, but others produced a sequence of two or three tones or a musical melody.[5]
The first commercial mobile phone with customizable ring tones was the Japanese NTT DoCoMo Digital Mova N103 Hyper by NEC, released in May 1996.[6] It had a few preset songs in MIDI format. In September 1996, IDO, the current au, sold Digital Minimo D319 by Denso. It was the first mobile phone where a user could input an original melody, rather than the preset songs. These phones proved to be popular in Japan: a book[7] published in 1998 providing details about how to customize phones to play snippets of popular songs sold more than 3.5 million copies.
The first downloadable mobile ring tone service was created and delivered in Finland in autumn 1998 when Radiolinja (a Finnish mobile operator now known as Elisa) started their service called Harmonium, invented by Vesa-Matti Pananen.[8] Harmonium contained both tools for individuals to create monophonic ring tones and a mechanism to deliver them over-the-air (OTA) via SMS to a mobile handset. On November 1998, Digitalphone Group (SoftBank Mobile) started a similar service in Japan.


Free Ringtones
Free Ringtones
Free Ringtones
Free Ringtones
Free Ringtones
Free Ringtones
Free Ringtones
Free Ringtones
Free Ringtones
Download Free Ringtones Wallpaper Mp3
Free Ringtones And Wall Papers Of Kid Assassin

LinkWithin

Related Posts Plugin for WordPress, Blogger...